Home > Error Code > Sn Error Code Hot Tub

Sn Error Code Hot Tub

Contents

The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. COL = Cool condition. Under NO circumstances should a pump be allowed to run without priming beyond the end of the 4 minute Priming Mode. navigate here

Low speed pump and heater will activate until spa reaches 65°F. This error will usually lock out the system to where nothing will operate. Master Spa is registered tradmark of Master Spas, Inc. ©2003-2016 Master Spa Parts. Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions.

How To Fix Sn Code On Hot Tub

Spa Error Codes: Sn, Sn2, Sn3, EO, E1, Prr With these spa sensor codes, the Temperature Sensor is open or shorted. balboawatergroup 14,815 views 4:17 # 27 Hot Tub Heater Replacement for 240 volt hot tubs. - Duration: 6:27. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. If there is No Error Message, Select "No Error Message" Below.

  1. Powered by vBulletin Copyright © 2016 vBulletin Solutions, Inc.
  2. Check for proper spa water level and ensure pump is primed.
  3. Closed Slice Valve.7.
  4. The temp sensor is the larger of the two silver bullets.

System will Auto Reset when Water Temp is below 108°F (42.2°C). Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Hot Some Spa Brands or Models may have this Message Enabled, and the Interval between these Messages will be whatever the Spa Manufacturer has selected. Balboa Sn Error Code George Makris 36,426 views 5:36 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09.

After the Problem has been Resolved, you Must Press Any Button to Reset and Restart Heater Start Up. Underneath the spa, check that all valves are open (handles up). Back to Top rt9 or TEST GFCI Message Time to "Test GFCI Reminder" (rtg).Appears Every 30 Days*. http://www.troublefreepool.com/threads/70448-SN-code-on-Balboa-control Close Login or create an account to be rewarded for sharing your referral link!

Blocked Suction Fitting.3. Marquis Spa Error Codes If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the

Dr Code On Hot Tub

Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. Ecn = Spa operating in Economy Mode. How To Fix Sn Code On Hot Tub Autoplay When autoplay is enabled, a suggested video will automatically play next. Balboa Hot Tub Error Codes The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open

Doing this will give you full access to the forums, where you will be able to receive personalized advice concerning your pool. check over here Press "Mode" Button to Clear Message. There may be conditions that exist in which the spa control system will be unable to detect these conditions. At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature Vita Spa Error Codes

You should have gotten a flow code instead like FLC, FLO, or LF. Press any button to leave Standby mode and return to normal operation. dr = Inadequate water detected in heater. http://phabletkeyboards.com/error-code/smb-error-code-36.php If water is not flowing through the heater chamber fast enough, it gets too hot, and the safety high temp sensors go into action - just doing their job.

Monitoring the Sensors will Continue for 1 Hour. Balboa Hot Tub Codes Sl I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address The Real Time Clock keeps the Current Time of Day.

The temp sensor and the high limit are usually located on the heater housing, with 1-2 small wires coming off and connecting to your controller.

I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah Sign in Transcript Statistics 6,226 views 1 Like this video? Sign in to add this video to a playlist. Gecko Spa Pack Error Codes Share your referral link!

Back to Top HOt or HOT-CALL SVC Message A Pump appears to have been stuck ON before a GFCI trip, causing an extreme overheat.If the extreme overheat conditions are determined, a I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah Too Many Closed Jets.6. weblink Contact qualified service technician.

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Snb = Spa is shut down. Once again these can be caused by a flow issue. ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill).

softcellelectrical 128,513 views 6:27 Replace A Circuit Board On a BP2000 System - Duration: 5:49. This could indicate a flow problem. Ecn The hot tub is in Economy mode While in this mode your hot tub will only heat while it filters. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different.

SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. Heat Related Pump Not Running.8. drops. ILOC = Interlock failure - possible pump or ozone spike. (---) =Unknown water temperature. (Displays when first powered up after refill).