Home > Error Code > Spa Error Code Hh

Spa Error Code Hh

Contents

In rare cases (usually warmer climates), the circulation pump may also cause overheating. Press "Mode" Button to Clear Message. Open the spa cover to allow excess heat and steam to escape. Inspect these first:• Check slice or ball valves. my review here

If so, clean debris from the suction screens. All Automatic Functions Remain OFF during this time. If you seem to notice that pump 1 is constantly running low speed and never shutting off, you should double check your filter cycles settings as they may be set far Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in

Balboa Hot Tub Error Codes

To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes. Heater Start Up will begin again after about 1 Min. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. The error code says HH.

Press "Mode" Button to Clear Message. BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" In this case, if the extreme conditions are determined, the spa will display the StU message until the spa is shut down It will also set the HOt flag (HOt does Sl Code On Hot Tub The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue.

Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).Priming Mode has been Exited and the Pump has Not yet Cal Spa Error Codes Entire system is disabled. It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. Any one have this issues or suggestions.

Happy Hot Tubbin' Daniel Lara Hot Tub Works Tags: spa error codes, Spa Heater Elements, spa heaters This entry was posted on Tuesday, January 6th, 2015 at 6:58 am and Hot Tub Error Code Oh This indicates a Possible Problem with the System Board. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. You can only upload a photo or a video.

Cal Spa Error Codes

Check for Extended Pump Operation or High Ambient Temp, or contact your Dealer or Service Organization.Spa Water Cool Down• In order for the Spa Water Overheat Error Message to Automatically Reset Back to Top CFE or CONFIG ERROR Message There is a "Configuration Error" (CFE) in the Dip Switches or Configuration Settings.This Error Message indicates that the Dip Switch Numbers Displayed or Balboa Hot Tub Error Codes The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the Cal Spa Error Codes Ec These error codes are similar to the ones previous, however we will be looking at these at another angle.

Shut the power down, remove the two wires to the pressure switch/flow switch, find some sort of wire to join the wires, but don't do it yet. this page There is Not enough Water in the Heater to Start it. Note: This auxiliary freeze protection functions at all times, even when another fault condition has occurred and has otherwise shut the spa down. Fix my Pool and Spa is online now I have a Marquis Spa. Cal Spa Oh Code

Blocked Suction Fitting.3. If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open If all these test are checked and they did not solve the error code issues, then it is possible you have a defective hi limit sensor. http://phabletkeyboards.com/error-code/smb-error-code-36.php Changed water and put in new filters.

The Persistent Memory Retains all of the Programming Information, such as Filter Cycles, Set Temp, User Settings and Configuration Settings, and does not require any form of Power or Battery for Hot Tub Overheating Troubleshooting All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 30 Days, but some Spa Brands or Models may be Different. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles.

Press "Mode" Button to Clear Message.

  1. Sometimes young guys simply are curious and want to experience something with a friend, such as masturbation.
  2. If there is Now an Error Message, select Message Other than PSt or Persist Fail below.No Error Messages3.
  3. See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end.
  4. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different.
  5. Add pH Decreaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message.
  6. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2.
  7. Touch any button to reset the system.
  8. DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional.

Read our FAQ! Spa wont respond This answer was rated: ★ ★ ★ ★ ★ I have a Marquis Spa. Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. Balboa Spa Control Manual There may be conditions that exist in which the spa control system will be unable to detect these conditions.

The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. Spa unusable. Contact your Dealer or Service Organization. useful reference If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below.

Unit will run on economy mode and not fault but not on standard mode. If there is Now a Message Other than a "rtC" or "RTC FAILURE" Real Time Clock Error Message, that Message will Now have to be Diagnosed. With the the Pump ON, prior to Heater ON, the Sensors differ by more than 2°F (1.0°C), indicating one or both Sensors are several degrees off. Hold = Panel sensors have been pressed too many times in a short period of time.HOT = Circuit Board temperature has exceeded acceptable limit.ICE = Freeze protection.

See M7 Sensors here. Clean and Condition Wood per Manufacturers Instructions. Press any Button except "Jets 1" to Exit and Return to Normal Operation. Check for proper spa water level and ensure pump is primed.

Hope it all works well for you. Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common