BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" Power on the spa must be cycled before the heater will function again. Press "Mode" Button to Clear Message. Spa has shut down. navigate to this website
All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 30 Days, but some Spa Brands or Models may be Different. Press "Mode" Button to Clear Message. This must be repaired only be a Sundance Spas dealer or qualified service technician. Some panels need a prompt from you to restart.
Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. Any and all service should be performed by a licensed spa technician. Program setting of spa unit for Economy Mode.3.
Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi Hot Tubs & Spas is headquartered in Chino, California. Jets pump 1 will likely deactivate, also. 1. Indicates a shorted sensor and the heater is disabled. How To Fix Flo Error Hot Tub All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different.
ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement Balboa Hot Tub Error Codes OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally.
Back to Top SbY or STANDBY MODE Message The Spa is Operating in the "Standby" (SbY) Mode.All Automatic Spa System Functions are Disabled so that Pumps and Blower will not turn Hot Tub Error Code Oh FREEZE PROTECTIONA potential freeze condition has been detected. Shut the spa down, remove the filter and make sure all the jets are open. This must be repaired only be a Sundance Spas dealer or qualified service technician.
The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the Contact a Jacuzzi hot tubs dealer or a service technician. – – – The water temp has raised above acceptable safety limits and triggered the safety “Watchdog” program of the spa Jacuzzi Error Code Fl1 Check for proper water level and for clogged filter (pages 60-62). Vita Spa Error Codes These error codes are caused by a variety of reasons.
The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2. useful reference Open the spa cover to allow excess heat and steam to escape. Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat. Each one uses it's own conventions for naming the various system faults. Marquis Spa Error Codes
If you need assistance with spa trouble codes, you can call us anytime at 800-770-0292 Happy Hot Tubbin' Daniel Lara Hot Tub Works Tags: hot tub error code, IC, ICE, ICE2 Freeze Condition detected; Warm up procedure begins. Take off the spa cover to allow the water to cool down.2. my review here These are usually presented as FL, FLO or FLOW on your display, although it may be LF, for Low Flow, or PS for Pressure Switch.
Contact your Dealer or Service Organization. Great Lakes Hot Tub Error Codes Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat. Spa may be partially deactivated or low speed pump (and air blower if equipped) may activate to lower temp OHH Overheat.
Closed Slice Valve.7. a) Remove filter cartridge in order to purge the air lock from the circulation pump intake. Water temperature has reached 118ºF. Jacuzzi Error Code 616 You can leave a response, or trackback from your own site.
Contacta Jacuzzi hot tubs dealer or a service technician. OH, OHH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights Temperature Sensor Failure. No Automatic Functions will turn ON during this time, and the Heater will Not Start. get redirected here Back to Top DETAILED PRIMING INSTRUCTIONS CONTINUED If you had to turn off power to the spa before both pumps primed, leave the spa off (with water in it) for at
The spa deactivates in this situation. Jets pump(s) operate until the hot tub is out of danger. *Note: The error commonly occurs when the hot tub is first filled because tap water is often very cold. Heater disabled but the spa is operational.PSoC = Pressure switch open with circulating pump.PSoL = Pressure switch open with low pump.PSoH = Pressure switch open with high pump.ToE = Time out If there is Now a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, contact your Dealer or Service Organization.
No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address Hot tub covers • Cover lifters • Hot tub filters • Chemicals • Accessories Visit Our Official Site Backyard Blast By TheCoverGuy.com 2016. Shut the spa power off, remove the filter and make sure all the jets are open.
Note: Internal freeze protection only functions when there is proper power running to the spa, and the control system is operational. Heater disabled but spa operational SH Short circuit on temperature sensor Sn1 Hi-Limit fault, water may be dangerously hot Sn2 Temperature sensor fault, Heater deactivated Sn3 Temperature sensor fault, Heater deactivated OPEN SENSOR (heater disabled) or SHORTED SENSOR (hot tub deactivated) The high-limit temperature sensor is non-functional. Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue.
If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Contact the dealer or service technician if the problem continues. Leave a Reply Click here to cancel reply. This must be repaired only be a Sundance Spas dealer or qualified service technician.
If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. This setting is not user-programmable.