Home > Error Code > Spa Error Messages

Spa Error Messages

Contents

a) Remove filter cartridge in order to purge the air lock from the circulation pump intake. Too Many Closed Jets.6. Do not use spa when temperature is flashing or the OH message is displayed. Ecn = Spa operating in Economy Mode. navigate to this website

Closed Slice Valve.7. On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States After about 45 Seconds, Check for Error Messages on the Topside Panel Display. A sloid white light indicates that all operations are normal.

Jacuzzi Error Code Fl1

a) Remove filter cartridge in order to purge the air lock from the circulation pump intake. Do not attempt to service on your own. If there is Now a Message Other than a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, that Message will Now have to be Diagnosed. c) Get an assistant to help turn the water on for 30 seconds.

DO NOT ENTER THE WATER! Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions. Contact ACC. Artesian Spa Error Codes If water is not flowing through the heater chamber fast enough, it gets too hot, and the safety high temp sensors go into action - just doing their job.

When water doesn't flow fast enough through the heater, it removes less heat, and the temperature of the water increases. These error codes can be caused for several different reasons. The error codes above are related to a temperature sensor failure, overheat problems or a flow problem. ONLY USE FINGER TIGHTENING METHOD!4.

This condition does not kick in until the water temperature climbs to 95°F (35°C). How To Fix Flo Error Hot Tub You can leave a response, or trackback from your own site. Heat Related Pump Not Running.8. Try unplugging topside and plugging into another port.

Balboa Spa Control Manual

This indicates a Problem with the Firmware (Operation Program), or the System is Operating on Unreleased Firmware (Sample or Prototype System). The Jacuzzi Spa J-135 hot tub  is a 6 person entry level hot tub. Jacuzzi Error Code Fl1 ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement Sl Code On Hot Tub The J- 385 features four deep bucket seats.

Email Address: Bath/Spa Professionals Homeowners Home | Contact Us | About Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Terms & Conditions | Cannot Find No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. Rare system error. However, the usual cause for spa temp sensor error codes is that the water flow is insufficient, and when water moves too slowly through the heater, it doesn't remove the heat Vita Spa Error Codes

Spa Models Jacuzzi Hot Tubs LX Collection Error Codes Jacuzzi Hot Tubs J-400 Error Codes Jacuzzi Hot Tubs J-300 Error Codes Jacuzzi Hot Tubs J-200 Error Codes Jacuzzi Hot Tubs and Please note: Filter cartridges should be cleaned daily! 2. drops.hot = Overheating, water over 112° F. http://phabletkeyboards.com/error-code/sony-computer-error-messages.php FREEZE PROTECTIONA potential freeze condition has been detected.

The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition. Marquis Spa Error Codes FL = Flow. The pump should only be restarted when the water temperature reaches 6C (43F). 2.

OH One of the sensors detected that the water in the hot tub is 112°F (44°C).

After starting or during the functions of filtering or/and heating, the water flow sensors do not detect water flow. 1. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. In both cases, the spa heater will deactivate. Great Lakes Hot Tub Error Codes Underneath the spa, check that all valves are open (handles up).

If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the Remove the filter/debris bag for and clean or replace. Blinking Heater Icon Icon flashes on and off to let you know that the temperature sensor has detected either a temperature difference of-20°F (6°C) difference between set and actual temperature ortemp Slp The hot tub is in Sleep mode.

Stands for “Overheat”- and the tub shuts down because water temp is too hot. Heater is deactivated. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Heater is deactivated.FL1 = Water flow problem, inhibited or pressure switch malfunction.

SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. Please contact the Bestway UK Aftersales Team 4. All Rights Reserved. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or Continue for a Detailed Test Procedure.WARNING:A Heater Overheat Error Message may indicate Excessively High Heater Temperatures which

PSoC = Pressure switch open with circulating pump. The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2. No corrective action is necessary. You Must Press Any Button to Reset when Water is below 108°F (42.2°C).

Quick View Troubleshooting Display Messages for 880 Series Aspen™ - Maxxus™ - Optima® - Cameo® - Majesta® - Altamar™ - Capri® There are a number of unique functions designed into your The Spa or Hot Tub Panel Displays: HL, HFL - This indicates that a substantial difference in temperature between sensors has been detected during heating. - This could indicate a flow