Home > Error Code > Spa Error

Spa Error

Contents

After about 45 Seconds, Check for Error Messages on the Topside Panel Display. OPEN SENSOR (heater disabled) or SHORTED SENSOR (hot tub deactivated) The high-limit temperature sensor is non-functional. MessageMeaningAction Required No message on display. Power has been cut off to the spa.

Water temperature is above acceptable limits.DO NOT ENTER THE WATER! error codes Hot tub covers hot tubs jacuzzi Jacuzzi errors jacuzzi hot tub models Jacuzzi Hot Tubs and Spas jacuzzi owners manual spa covers spas Share This Previous Post← How to The J-355 has a small but good step to enter the hot tub. Refill, if necessary.

Balboa Hot Tub Error Codes

If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and ACC (Applied Computer Controls)Systems for Spas or Hot Tubs: CoLd = Temperature in the spa heater housing is below 40° F. The Cover Guy manufacturers custom hot tub covers for all the Jacuzzi Spa models. SEoP = Sensor open or disconnected.

  1. Back to Top SAL or SANITIZER LOW Message At the ORP Sensor, the "Sanitizer Level is Low" (SAL).With an ORP Sensor Installed in the System, the Sanitizer Level is Below 740
  2. Other Heating Modes are Economy, Standard in Economy, and Sleep Modes.Note: On the Panels that Display the "Std" or "St" Messages, the Message will Only be Displayed for a Few Seconds
  3. SESH = Sensor short, nonfunctional.
  4. See "Water is too hot" (page 77).
  5. PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected.
  6. On EL and GL Systems Only, equipped with a "Mode" Button, the Ozone Generator can be Turned ON for 15 Seconds and OFF by using the "Mode" Button.
  7. One sensor has detected 110°F.

Blocked Suction Fitting.3. Some Spa Brands or Models may have this Message Enabled, and the Interval between these Messages will be whatever the Spa Manufacturer has selected. Sundance Spa or Hot Tub Control Systems: ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific)Hold = Panel buttons Vita Spa Error Codes Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1.

The Jacuzzi Spa J-385 hot tub spa is a 6 person hot tub. Jacuzzi Error Code Fl1 The Real Time Clock keeps the Current Time of Day. Indicates a shorted sensor and the heater is disabled. The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature.

When water doesn't flow fast enough through the heater, it removes less heat, and the temperature of the water increases. Marquis Spa Error Codes Add pH Decreaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message. Pressure switch is not working. Error Logo Light Meaning Overheat Protection (Heater is deactivated, filter/circulation pump is activated).

Jacuzzi Error Code Fl1

In both cases, the spa heater will deactivate. b) Hold a garden hose over filter cartridge wall fitting and utilize a rag to make a seal around hose end. Balboa Hot Tub Error Codes Slp The hot tub is in Sleep mode. Hot Tub Error Code Oh It automatically activates all of the pumps and the blower to circulate water and warm the plumbing.

By the ‘90s, these hot tubs had expanded into backyard models, and the award-winning company spread out into the international market by the year 2000. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention. SnA & SnB Spa is shut down. How To Fix Flo Error Hot Tub

Closed Slice Valve.7. Try and clean your filters. Snb = Spa is shut down. Balboa Control Systems for Spas or Hot Tubs: pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.OHH = Overheat.

Consumer Reviews EasyPak Spa Controls "Very pleased with the ease of installation and all the diagnostic features that other spa packs did not even have. Balboa Spa Control Manual Your hot tub is only scheduled for filter 2 times a day for 2 hours. What causes a Spa to Overheat?

Back to Top Pr or PRIMING MODE TAKES 4 MIN Message The Spa is Operating in "Priming" (Pr) Mode.The Spa has just been powered up and is in Priming Mode for

Contact dealer or a service technician if problem continues. The spa topside panel messages include common diagnostic messages, operational messages, and various other messages such as reminders. Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa Great Lakes Hot Tub Error Codes If alternating with temp, may be temporary condition.

Pump may also be deactivated). Open Sensor Means temperature sensor is malfunctioning; heater is taken offline automatically when this happens. Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the If buzzing sound or lack of sound is detected, cut off the water to the hot tub – may indicate that pump is notproperly primed.

Heat Related Pump Not Running.8. This indicates a Possible Problem with The System Board. Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat. Heat Related Pump Not Primed.9.