Home > Error Code > Spaform Hot Tub Error Codes

Spaform Hot Tub Error Codes

Contents

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. WARNING, if you go too far the pressure switch may activate with the pump off. Ask Your Own Pool and Spa Question Customer: replied4 years ago. This indicates a Possible Problem with the System Board. my review here

Heat Related Pump Not Primed. Heat Related Pump Not Primed.9. And also changed sensor. (Also bought new filters) not sure where to go next? Contact your Dealer or Service Organization.

Balboa Hot Tub Error Codes

You should check that your GFCI is working properly every 30 days as per manufacturer’s instructions. If alternating with temperature, it may just be a temporary condition. Back to Top Pr or PRIMING MODE TAKES 4 MIN Message The Spa is Operating in "Priming" (Pr) Mode. As a responsible adult, always check the control panel display for errors and verify safe water temperature before using a spa, and before allowing children to use a spa.

System will Auto Reset when Water Temp is below 108°F (42.2°C). ian Ranshaw October 10, 2015 at 6:18 pm Hi. Heat Related Pump Not Primed. Marquis Spa Error Codes this information is being provided for informational purposes only.

Back to Top LF or LOW FLOW Message There is a Verified "Low Flow" (LF) Condition in the Heater.The "HFL", "HL", or "HTR FLOW LOW" Fault has occurred 5 times in These error codes are similar to the ones previous, however we will be looking at these at another angle. These error codes can be caused for several different reasons. The light did come on above the heat sign but the flo error was still there.

Follow action required for HEATER MAY BE DRY -WILL RETEST SHORTLY message. Great Lakes Hot Tub Error Codes Add Sanitizer according to Manufacturers Instructions. DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional. I am out of options….I did make sure I went in to Standard mode… any suggestions?

Spa Error Codes

This is a normal spa function; no further action is necessary. Number two pump still inop. Balboa Hot Tub Error Codes Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization. How To Fix Flo Error Hot Tub Back to Top Your cart is empty.

I be the PC board needs to be replaced.-Jay admin October 10, 2015 at 7:34 pm Hi Pete,Sounds like either bad sensors or a bad PC board.-Jay admin October 10, 2015 this page Dirty Filter.5. Back to Top rtr or TREAT WOOD Message Time to "Treat Wood Reminder" (rtr). Remove the Spa Cover and allow Sanitizer to Dissipate, or do a Partial Water Change. Vita Spa Error Codes

Back to Top PHH or PH IS HIGH LOWER PH Message At the pH Sensor, the "pH Level is High" (PHH).With a pH Sensor Installed in the System, the pH Level Either wait for the Potential Freeze Condition to End, or contact your Dealer or Service Organization. No Automatic Functions will turn ON during this time, and the Heater will Not Start. get redirected here Heat Related Pump Not Primed.

Blocked Skimmer. Hot Tub Error Code Oh To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes. Hold = Panel sensors have been pressed too many times in a short period of time.HOT = Circuit Board temperature has exceeded acceptable limit.ICE = Freeze protection.

Heat Related Pump Not Primed.

Heat Related Pump Not Primed. Spaform Prestige 75 hot tub is the best spa Spaform has made to date. A "Cyclic Redundancy Code" (CrC) is a type of checksum algorithm that takes a string of data bytes and calculates from it a few bytes (the checksum) that depend on the Hydropool Hot Tub Error Codes Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions.

Spa Water Cool Down In order for the Spa Water Overheat Error Message to Automatically Reset and Clear, the Spa Water Must Cool to below 108°F (42.2°C). Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).Priming Mode has been Exited and the Pump has Not yet Back to Top ICE, IC, or FREEZE COND Message A Potential Freeze Condition has been Detected, and "Ice" (ICE) in the System is being Prevented.44°F (6.7°C) or Lower has been Detected useful reference The Water Temperature is Sampled Only during Programmed Filter Cycles.

Switch closed while pump is deactivated.COL = Cool condition. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or Continue for a Detailed Test Procedure.WARNING:A Heater Overheat Error Message may indicate Excessively High Heater Temperatures which SENSOR SYNC Sensors are out of balance. This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally.

Press any topside button to restart. Too Many Closed Jets.6. Click here for the SpaForm User Guide and Owners Manual Spaform_Owners_Manual Tags: error codeshot tubhot tubsspaspa form spasspaformspas Recent Posts SpaForm Spa Information & Error Codes The Hot Tub Life!