Home > Error Codes > Spa Control Panel Error Codes

Spa Control Panel Error Codes

Contents

DO NOT GET INTO THE WATER. Check for dirty or clogged filter cartridge.3. Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Contact the dealer or service technician. http://phabletkeyboards.com/error-codes/snd-pcm-write-error-codes.php

SESH = Sensor short, nonfunctional. Heat Related Pump Not Primed. Error Logo Light Meaning Overheat Protection (Heater is deactivated, filter/circulation pump is activated). Jet pumps 1 and the heater activate automatically to bring the temp to 15°F (8°C) of the settemps.Note: this condition often occurs when filling the spa with water since tap water

Balboa Hot Tub Error Codes

One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit This condition does not kick in until the water temperature climbs to 95°F (35°C). With the the Pump ON, prior to Heater ON, the Sensors differ by more than 2°F (1.0°C), indicating one or both Sensors are several degrees off.

The Persistent Memory Retains all of the Programming Information, such as Filter Cycles, Set Temp, User Settings and Configuration Settings, and does not require any form of Power or Battery for OH = High temperature condition, has reached 110°F. If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and Balboa Hot Tub Turn Off Economy Mode LF, or Low Flow error codes on a spa or hot tub is really a self-preservation exercise for your hot tub.

Replace UV bulb (you can get one from your authorized Jacuzzi dealer). Balboa Spa Control Manual Contact dealer or a service technician. Some panels need a prompt from you to restart. d) Replace the filter cartridge and verify the solution worked.4.

Either wait for the Potential Freeze Condition to End, or contact your Dealer or Service Organization. Marquis Spa Error Codes The Jacuzzi Spa J-135 features two deep bucket seats for the and a lounge. The spa deactivates in this situation. One sensor has detected 110°F.

Balboa Spa Control Manual

If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Balboa Hot Tub Error Codes Contact your Dealer or Service Organization. Balboa Hot Tub Codes Sl The causes of low water flow in a spa include: Dirty spa filter cartridge Closed or partially closed valves or jets Pump has an air lock, or has lost prime Low

The Spa or Hot Tub Panel Displays: Sn, SnS This indicates that the sensors are out of balance.If alternating with temperature, it may just be a temporary condition. http://phabletkeyboards.com/error-codes/snd-pcm-readi-error-codes.php This condition often occurs when filling the spa with water since tap water is usually cold. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. Vita Spa Error Codes

Indicates a shorted sensor and the heater is disabled. The J- 575 features two deep bucket seats for the and one deep sitting lounge for best relaxation. The J-575 also has a nice step to enter the hot tub. HFL = Substantial difference between temperature sensors detected. http://phabletkeyboards.com/error-codes/soap-api-error-codes.php It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing.

drops. How To Fix Flo Error Hot Tub Contact the dealer or service technician. Contact the dealer or service technician.

Blocked Suction Fitting.3.

Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. b) Hold a garden hose over filter cartridge wall fitting and utilize a rag to make a seal around hose end. If itwill not reset, check for clogged filters. Spa Command Panel Instructions Blocked Skimmer.4.

Turning it on will reset cycle for the circulation pump. Contact a Jacuzzi hot tubs dealer or a service technician. – – – The water temp has raised above acceptable safety limits and triggered the safety “Watchdog” program of the spa Back to Top drn or DRAINING Message While in Standby Mode, "Drain" (drn) Mode has been Activated.The "Jets 1" Button has been Pressed while in the Standby Mode, and Pump 1 useful reference Heater disabled but the spa is operational.

FL2 = Pressure switch problem. The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the Take off the spa cover to allow the water to cool down.2. There are 3 groups of error codes; Flow codes, relating to water flow, Heater codes, and Sensor codes.

Let's start at the top, today's post is about water flow trouble codes on your spa panel. Adding cool water may be necessary. Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming Heat Related Pump Not Primed.

Heat Related Pump Not Primed. Leave a Reply Click here to cancel reply. Both are secured with black plastic nut around the gray cable. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or Continue for a Detailed Test Procedure.WARNING:A Heater Overheat Error Message may indicate Excessively High Heater Temperatures which

PSoH = Pressure switch open with high pump. The final problem could be the pressure switch/flow switch itself. Contact dealer or a service technician if problem continues. If alternating with temp, may be temporary condition.