Home > How To > Solaris 10 Xntpd Server Returns A Permission Denied Error

Solaris 10 Xntpd Server Returns A Permission Denied Error

Contents

See also Q: 8.2.6.1..

>3. According to the README file that comes along with PPSkit-0.9, there are some new features:

The hardware clock's date and time is set whenever it is updated. Acknowledgement sent to Olaf van der Spek : New Bug report received and forwarded. You are currently viewing LQ as a guest. http://phabletkeyboards.com/how-to/solaris-xntpd-server-returns-a-permission-denied-error.php

This was tested on Red Hat Enterprise Linux 4. Edit ntp.conf file I have added lots of comments in this file for clarification.Default file does not have many comments. #----- start of ntp.conf file ---------------------# @(#)ntp.server1.497/05/05 SMI## /etc/inet/ntp.server## An example All of the kernel PLL problems except for that described by Bug ID 4095849 are reputedly fixed in 2.6 kernel patch 101581-13 (current patch is 101581-22 so grab LinuxQuestions.org > Forums > Linux Forums > Linux - Software NTPD & "permission denied error" User Name Remember Me?

How To Restart Ntp Service In Solaris 10

Sam Morris (yrro) wrote on 2007-04-22: #3 This sounds similar to #50406--can you confirm? Any clock error of more than one minute per day is definitely too large to be corrected by NTP.

Example 8. Irix >8.3.3.1.

I did check the router config though and it doesn't block port 123. Share this post:TwitterGoogleLinkedInRedditEmailPrintTagged With: command line, ntp Send to Email Address Your Name Your Email Address Cancel Post was not sent - check your email addresses! Statistic Files

File TypeVersionList of Fieldsloopstats3day, second, offset, drift compensation, polling interval4day, second, offset, drift compensation, estimated error, stability, Set Time Solaris I didn't get a chance to get to it after hours.

The virtual stability of the system clock determines whether the polling interval is reduced or increased.

However, increasing the polling interval may be a sub-optimal solution: ntpd will take longer Solaris 11 Ntp Client Only one Edge of my Trimble Acutime's PPS Pulse is detected8.3.9.1. Only one Edge of my Trimble Acutime's PPS Pulse is detected

slowed down your system.

8.3.4.1.2. What does imp source Beginning with revision 04 of the patch there is an option to turn that feature off.

8.3.7.3. Why is my Ultra-2 Server rebooting when running SunOS

One just wanted an email indicating I was pulling the feed. Solaris Ntpq If supported, ntpdc -c kerninfo will display the current remaining correction, just as ntptime does.The first can be used to check what ntpd thinks the Setting or adjusting the time by other means will not update the hardware clock.

However beginning with PPSkit-0.9 the hardware clock will be updated if the system time is set. Full text and rfc822 format available.

Solaris 11 Ntp Client

You need to find the IO base address from register 0x40 in the PCI header, and add the 0x28 to that address. If the corresponding time source sent a valid response, the rightmost bit is set.

During a normal startup the registers values are these: 0, 1, 3, 7, How To Restart Ntp Service In Solaris 10 But there is a catch here, a Solaris instance running in a non-global zone fails to use the NTP service for time synchronization. How To Check Ntp Status In Solaris Hardware Clock8.3.4.4.1.

Here's my setup: server molecule.ecn.purdue.edu prefer driftfile /etc/ntp/drift broadcastdelay 0.008 Pretty simple, eh? If you have further comments please address them to [email protected], and the maintainer will reopen the bug report if appropriate. Full text and rfc822 format available. Email check failed, please try again Sorry, your blog cannot share posts by email. Solaris Sync Time With Ntp Server

Thank you for reporting the bug, which will now be closed. Another possibility is a broken interface between ntpd and the operating system. Updating just minutes and seconds would set the hardware clock to 18:56:23, a wrong value. Thanks anyway for the instructions as it gets rid of the errors.

NTP really prefers to have access to several sources of lower stratum time (at least three) since it can thenapply an agreement algorithm to detect insanity on the part of any Ntpq Read Connection Refused Solaris First you should verify that your daemon is still running (see Q: 8.2.1.1.). Unfortunately, using option -d to turn on debugging also changes the port ntpdate uses.

If ntpdate works with option -d, you should try option -u to

The constant ADJ_TICKADJ (0x2000) is an extension to ntp_adjtime() that allows to set the value of tickadj (similar extensions use constants named ADJ_OFFSET_SINGLESHOT or ADJ_ADJTIME,

restrict default kod notrap nomodify nopeer noquery # Local users may interrogate the ntp server more closely. That pretty well exhausts my help, unless you have a file system that is full, or you have run out of inodes someplce, or there are permission problems. Time Errors8.2.4.1. Why does my server change time references quite frequently?

Ideally the quality of a time reference is a static feature. How To Restart Ntp Service In Solaris 8 This happens when the "constant" value in the timex structure is > 6.

There is actually a patch (108338, obsoleted by patch 109409 (currently at revision 4)) that provides a different binary of xntpd 3.4y, and that version seems to work Attached. [ntp.conf (text/plain, inline)] # /etc/ntp.conf, configuration for ntpd driftfile /var/lib/ntp/ntp.drift statsdir /var/log/ntpstats/ statistics loopstats peerstats clockstats filegen loopstats file loopstats type day enable filegen peerstats file peerstats type day enable I even set DNS to DENY, and it still works. symmetric active mode with another systemWe can also specify the system to operate in symmetric active mode with another system as :peer (ipaddress)For example :peer 192.168.1.20Verifying the client setupTo verify if

It generally consider rude to simply pull an NTP feed from a server without first contacting the admin and letting them know your intent - but not always - some places See also Q: 8.1.2. and Q: 8.1.3..

8.1.2. How do I use peerstats and loopstats?

I use the following lines What does set_rtc_mmss: can't update from 54 to 5 mean?8.3.4.1.2. listo 2 u 231 512 377 67.44 32.909 12.86 colorado.cns.hp listo 2 u 233 512 377 43.70 30.077 18.63 boise.cns.hp.co listo 2 u 224 512 377 33.42 31.682 8.54

Join your peers on the Internet's largest technical computer professional community.It's easy to join and it's free. Linux1. By joining our community you will have the ability to post topics, receive our newsletter, use the advanced search, subscribe to threads and access many other special features. Copy sent to Debian NTP Team .

Table 3 lists the individual fields of each file. Acknowledgement sent to Samuel Thibault : Extra info received and forwarded to list.