Home > Smart Error > Smart Error Wp At Lba

Smart Error Wp At Lba

SirMaster, Dec 19, 2014 #8 angelus249 Newbie Joined: Dec 19, 2014 Messages: 24 Thanks Received: 4 Trophy Points: 6 Thanks gentlemen for all the feedback! I have been asked 3 times in the past few years to write a book on the subject, and I was asked repeatedly at my previous job to write a very Self-test supported. angelus249 Newbie Joined: Dec 19, 2014 Messages: 24 Thanks Received: 4 Trophy Points: 6 Hello together, I run the latest 9.3.0 with all updates, 4x 4TB in a RAID-Z configuration. Source

My friend said this unit worked well once, but at some point in the past, it started going south to the point where it is now. There is also the possibility > that something found on the web might completely trash a disc anyway. Don't ask us to compare or recommend products. How is being able to break into any Linux machine through grub2 secure?

When there are no more bad sectors, keep doing it for a week. It doesn't seem to have lasted very long. Here's the uncorrectable error log : Complete error log: SMART Error Log Version: 1 ATA Error Count: 2534 (device log contains only the most recent five errors) CR = Command Spinrite - and yeah, I've used that way back in the past, but even still, modern hard drives tend to continue to fail once they start.

Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Already contacted my supplier to get a replacement drive. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Location: GA, USA A scrub does not force a read of all sectors, but a long SMART test should.

Self-test supported. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 1b fb 6b 00 Error: WP at LBA According to the Google hard drive survey from 2007 it's about 21 times as likely to fail in the next three months as a drive without these errors, which is quite http://www.dslreports.com/forum/r27448443-hard-drive-gsmartcontrol-data-interpretation-needed The time now is 16:00. © 2015 SUSE, All Rights Reserved.

SCT Error Recovery Control supported. Reallocated sectors and reallocated events are not great, but I have seen enough disks that operate fine for years with a low number of these. Which residential routers are fast and secure with continued updates? [Networking] by WhyADuck464. Self-test supported.

  1. Conveyance Self-test supported.
  2. more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science
  3. Yeah, … The errors contributed, … WP -- Austin Hicks (9-0).
  4. share|improve this answer answered Apr 19 '12 at 9:18 cstamas 5,2431234 add a comment| up vote 2 down vote Read errors can be caused by something as simple as losing power

Short self-test routine recommended polling time: ( 2) minutes. https://www.neowin.net/forum/topic/1257094-get-uncorrectable-error-in-data-error-in-my-hard-drive-error-log-is-it-failing/ The term "extended" here is too vague -- there are many internal SMART tests which run for extended periods of time: long, select, and (on some drives) conveyance.I have a feeling Not the answer you're looking for? The WebGUI storage section gives me a healthy status, however I seem to have a problem with my ada3 disk.

In fact, I wouldn't bother trying to figure it out either -- the drive is in too bad shape for me to really care.I ran those short tests. this contact form If Selective self-test is pending on power-up, resume after 0 minute delay. See vendor-specific Attribute list for failed Attributes. However, that's 61 times within 644 hours.

Editing to add the information asked by OSPFv3 5 commentsshareall 5 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]OSPFv3Trusted 2 points3 points4 points 2 years ago(2 children)Run the trial of this software on it. You seem to have CSS turned off. SCT capabilities: (0x003d) SCT Status supported. have a peek here SCT capabilities: (0x003d) SCT Status supported.

it's at 361, then 4 sectors get reallocated, so the number becomes 357).SMART attribute 197 indicates you have 2 LBAs which the drive considers "suspect" thus cannot be read (you'll receive Check the warranty status might have an day or two left. You can blame Toshiba for this one.

The real problem is when these numbers regularly rise meaning there is some mechanical/electromagnetic issue with the drive and you will soon exhaust the spare sectors.

For me, yes. :) I have run gsmartcontrol a few times in the past,. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. linux smart drive-failure share|improve this question edited Apr 19 '12 at 9:21 cstamas 5,2431234 asked Apr 19 '12 at 8:29 c2h2 4292516 ok soz, done now. –c2h2 Apr 19 After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 --

The disks are fairly new. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the This drive is in bad shape and should not be used going forward. http://phabletkeyboards.com/smart-error/smart-error-5.php I can tell from this line:ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW _VALUE Note the space after RAW and before _VALUE.

Total time to complete Offline data collection: ( 4800) seconds. You can use the disk as long as you don't expect to read the data. Attention to Telemetry updates 'preview' for Win 7 / 8.1 [Microsoft] by chachazz260. ForumsJoin Search similar:Uninstalled win8, but now neither win7 or DBAN works[hard drive] Hard drive failureMore adventures in data recovery[hard drive] Calling koitsu for his valued opinion...[hard drive] need to transfer files

Total number of times is 61. Not that we can get our hands on the utility and personally I wouldn't fancy using it on a truly worn out drive. smartctl -a X: > C:\smart.txt where X: is a filesystem/partition on the drive which you want stats for3. Briefly describe the problem (required): Upload screenshot of ad (required): Select a file, or drag & drop file here. ✔ ✘ Please provide the ad click URL, if possible: Home Browse

The situation of the OP is intermediate: he has sectors remapped and waiting. > Not that we can get our hands on the utility and personally I wouldn't > fancy using