Home > Smtp Error > Smtp Error 5.5.4 Unknown Rcpt To Parameter

Smtp Error 5.5.4 Unknown Rcpt To Parameter


All extended commands the server supports must be listed as part of the server’s response to EHLO, one per line, each line prefixed with code 250. Sorry it didn't work out. : does not like recipient. These problems are assumed to be under the responsibility of both sender and recipient, making clear that both must support a common set of formats or file types defined in the Could it be that at your site there is another relay in the outgoing path that constructs the MAIL FROM from the "From:" header attribute (which contains the friendly name - Check This Out

While other message transferring systems exist—some more efficient, some better at specific tasks, some privately owned and some public—none have won the widespread public acceptance of the venerable SMTP, first defined The reason why this might not have happened before Scalix is possibly that your old exchange system did not bother putting the display name in the From: header, so the relay This is a very typical Postfix error where the destination mailbox doesn’t exist. The system returned: (22) Invalid argument The remote host or network may be down.

Smtp Error Codes 550

X.4.4   Unable to route The mail system was unable to determine the next hop because there wasn’t enough routing information in the name resolution system. Having previously shipped mail products at Microsoft, she is now looking at grad school in a CS-related field so esoteric it doesn’t really have a name. BRGDS Bruno Top florian Scalix Posts: 3852 Joined: Fri Dec 24, 2004 8:16 am Location: Frankfurt, Germany Contact: Contact florian Website WLM Quote Postby florian » Thu Feb 01, 2007 7:00 Microsoft recommends using the WinRoute tool to troubleshoot this error (Microsoft Knowledgebase article 281382) 450 - Requested action not taken - The mailbox was unavailable at the remote end.

It must be used for all errors for which only the error class is known. Does > it have something to do with the .us domain? In general SMTP Error 450 is a transient error at the remote end (the destination), or at one of the servers en route to the remote end, and should induce your 5.5.0 Smtp 554 Therefore, on receiving an SMTP Reply 354 the sending server should send the body of the message to the receiving server and indicate the end of the message body with .

Unauthorize d usage can and will be prosecuted to the full extent of the law. More about the name change. the problem is that after i send the message, i get a failiure delivery message From: "Mail Delivery Subsystem" To: and the name Attachments if "Anonymous" file this info check it out As per Microsoft's documentation this error code is returned when either of the following conditions occurs : an SMTP connector is configured to use DNS without a smart host and also

Unauthorized usage can and will be prosecuted to the full extent of the law. Smtp Error 451 Because of this, a new set of codes were created. Gabbyy, Apr 24, 2008 #1 Advertisements William Smith Guest wrote: > When I tried to send an email to a certain address with a .us domain > I got the following This includes situations where the command is too long.

Smtp Error Code 554

Share this: Was this article helpful?How can we improve it?YesNoSubmit Bounced and Delayed MessagesLegitimate mail to group in moderation queue as spamGroup bounces every message it receivesAvoid bounced messages from new Does it have something to do with the .us domain? Smtp Error Codes 550 Cheers, Florian. 5.0 0 Smtp Going off of 2010 here but should be similar.

X.3.4   Message is too big for the system Mail is bigger than the mail size limit implemented by the mail server. his comment is here About the conversations here goes. For example, a 554 error returned by a Comcast server might look like this : "[email protected] SMTP error from remote mail server after initial connection : host mx2.comcast.net : 554 IMTA11.emeryville.ca.mail.comcast.net Please check the address and try again, or contact your system administrator to verify connectivity to the email system of the recipient.". -------------- In summary : most SMTP error 512 conditions Smtp Error 553

However, with the proliferation of spam, error 512 is also often encountered by automatic "out-of-office" replies to junk mail because the domain names used by junk mail are often bogus domain This code is useful with permanent failures. Tryry posted Oct 17, 2016 Loading... this contact form As above, the next attempt to send by your server may prove successful.

Example: 501 5.5.4 Syntax: MAIL FROM:

501 5.5.4 Syntax: RSET 501 5.5.4 Bad message size syntax 555 5.5.4 Unsupported option: k X.5.5   Wrong protocol version A protocol version mis-match existed What Does Http Server Code 200 Mean? R'ykandar Korra'ti SMTP, the Simple Mail Transfer Protocol, carries the electronic mail of the world. But how does SMTP work?

Type commands, and they’ll be processed and responded to with numeric response codes.

This status code should be used in successful delivery reports. If you try this and it doesn't work immediately give it ~5 minutes and try again. 0 Pimiento OP tomaspanta Feb 13, 2015 at 9:57 UTC 1st Post Creating your account only takes a few minutes. #5.5.0 Smtp 550 In the vast majority of cases SMTP Error 501 is caused by invalid email addresses.

invalid email address) Can sometimes also be indicative of communication problems (also called SMTP Error 5.0.1) SMTP Error 501 : The command was correct and recognised, but the parameters (the arguments, Best regards, Bruno Top florian Scalix Posts: 3852 Joined: Fri Dec 24, 2004 8:16 am Location: Frankfurt, Germany Contact: Contact florian Website WLM Quote Postby florian » Thu Feb 01, 2007 This is Scalix talking to postfix. navigate here This kind of codes force the sending MTA server to queue the message until it is successfully delivered or its time to live has timed out, usually this value is set

Recipient ok RCPT TO: [email protected] 250 2.1.5 [email protected] ... Florian. Valid SMTP e-mail addresses can contain only letters, numbers, hyphens, periods, and only one @ symbol. This code should be used as a permanent failure.

Please type your message and try again. Review our Bulk Senders Guidelines. 421, "4.7.0", Temporary System Problem. How IT Works: How Simple is SMTP? This code is useful for permanent errors.

The error message is effectively saying that the email addresses listed do not exist, or no longer exist (if you used to be able to email to them successfully). No machine MUST actually accept the syntax as it is incorrect. This can happen for example in very large corporation where the first email receiving server might only be an email exchanger server, a gateway server to the eventual server which holds If this error keeps occurring to the point that it has effectively lost its transient nature and has become .....