WinSock description: Same as Berkeley, and then some. WinSock description: Same as Berkeley. In this case, it might be possible to check the count of TCP RST packets received, or ICMP Port Unreachable packets. WSA_QOS_EOBJLENGTH 11022 Invalid QoS object length. weblink
WinSock description: Same as Berkeley. Does it means that i have a keylogger on my computer that tries to send e-mails? Detailed description: recv() and recvfrom(): if the datagram you read is larger than the buffer you supplied, then WinSock truncates the datagram (i.e. User suggestions: Check your WinSock, protocol stack, network driver and network interface card configuration. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx
See also: WSAEAFNOSUPPORT WSAEPROCLIM (10067) Too many processes. WinSock description: Similar to Berkeley. Check that your network system (WinSock implementation) has a utility that shows network statistics. For protocol and services resolution, the name or number was not found in the respective database.
This error is returned if an incorrect protocol is explicitly requested in the socket call, or if an address of the wrong family is used for a socket, for example, in The WSAEAFNOSUPPORT is the likely substitute error for this in WinSock, although its Berkeley meaning is slightly different. Basically, you want to identify where the problem occurred. What Is A Socket Error Berkeley description: A socket operation encountered a dead network.
Ran out of disk quota. WSA_QOS_EFLOWCOUNT 11023 Incorrect QoS flow count. The service provider procedure call table is invalid. https://kb.paessler.com/en/topic/333-how-do-i-solve-a-connection-refused-socket-error-10061-in-enterprise-console Detailed description: setsockopt(): WinSock generates this error if you try to set SO_KEEPALIVE but the connection has already been aborted (e.g.
The hostname is correct, but the FTP server is not listening on the port, there is no FTP server running, or a firewall is blocking the connection.10093 - Connection failed. Winsock Error 10053 WSAEFAULT 10014 Bad address. WinSock functions: accept(), bind(), connect(), gethostname(), getpeername(), getsockname(), getsockopt(), recvfrom(), send(), sendto(), setsockopt() if buffer length is too small. Try temporarily turning off the Windows firewall or any other software firewall you are running.10061 - Connection refused.
Detailed descriptions: connect(): the operation is underway, but as yet incomplete. Berkeley description: A socket operation failed because the destination host was down. Windows Socket Error 10054 error 10061 means -"connection refused. Socket Error 10061 Ppsspp WSA_QOS_EFILTERSTYLE 11019 Invalid QoS filter style.
Request refused: name server refuses to satisfy your query for policy reasons. http://phabletkeyboards.com/socket-error/socket-wsa-error-10061.php WinSock only allows a single blocking operation to be outstanding per task (or thread), and if you make any other function call (whether or not it references that or any other A connect request was made on an already-connected socket. In this case, the WSAEBADF error might mean the same as a WSAENOTSOCK error. Socket Error 10061 Connection Refused Windows 7
A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using sendto) no address was supplied. Make sure a local virus protection program does not block the connection. This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. http://phabletkeyboards.com/socket-error/socket-10061-error.php In fact, on occasion you can benefit if the WinSock implementation returns these other errors.
The host you were connected to crashed and rebooted. Socket Error 10061 Connection Refused Smtp In some cases these errors are platform dependent. WinSock description: Same as Berkeley TCP/IP scenario: In TCP terms (datastream sockets), it means an attempt to connect (by sending a TCP SYN packet) caused the destination host to respond to
TCP/IP scenario: Calling shutdown() with how=1 or how=2 sends a TCP FIN packet to the remote address, which literally means "I'm done sending." If the local host sent any more data WSAESHUTDOWN 10058 Cannot send after socket shutdown. A socket already has a type (a protocol), and each sockaddr structure has an address family field to define its format. Socket Error 10054 Connection Reset By Peer WinSock functions:
On the server end, you could use a network system utility similar to BSD's "netstat -a" command to check that your server is running, and listening on the right port number. TCP/IP scenario: A connection will timeout if the local system doesn't receive an (ACK)nowledgement for data sent. WinSock description: Same as Berkeley. http://phabletkeyboards.com/socket-error/socket-error-10061-e.php WinSock description: Partly the same as Berkeley.
Developer suggestions: Don't call bind() in a client application. Some invalid argument was supplied (for example, specifying an invalid level to the setsockopt function). Watch these 9 videos. Ignore it.
As you can see from the comprehensive list of WinSock functions, this error is the catch-all. An invalid value was given for one of the arguments to a function. Of the two that can fail, neither of them set an error value you can retrieve from WSAGetLastError() (refer to Chapter 10, "Support Routines" for more information on any of these Windows Sockets only allows a single blocking operation—per- task or thread—to be outstanding, and if any other function call is made (whether or not it references that or any other socket)
WSA_QOS_EUNKOWNPSOBJ 11024 Unrecognized QoS object. Any function that takes a socket as an input parameter--except close socket()--could potentially fail with this error. Berkeley description: The support for the socket type has not been configured into the system or no implementation for it exists. Berkeley description: A connect request was made on an already connected socket; or, a sendto() or sendmsg() request on a connected socket specified a destination when already connected.
Keep in mind that when you are having similar problematic behavior in multiple clients against the same server, it's more than likely a server problem Tweet Leave a Comment Please WinSock functions: the list of functions that explicitly list this error in the v1.1 Windows Sockets specification.